Products for cleaning outdoor flooring

DETERDEK

ACID DESCALING DETERGENT

For washing after installation: wet the surface beforehand with water. Then use DETERDEK diluted in a ratio of 1:5 or 1:10 (1 liter of product in 5 or 10 liters of water). Spread the solution a few square meters at a time, wait 2-3 minutes and then intervene vigorously with the brush or single-brush machine. Collect the residue with a rag or liquid vacuum cleaner and rinse with plenty of water. If stubborn dirt residues remain, repeat washing with more concentrated solutions. For extraordinary maintenance of external surfaces with obvious signs of aging (smog, dust...): dilute 1 liter of product in 10 liters of water. Then follow the same application methods described above.

FILA ALGAE-NET

ANTI-ALGAE DETERGENT FOR OUTDOORS

1) Wet the surface with water.

2) Apply the product with the appropriate spray or distribute it with a brush, sponge or airless pump.

3) Leave to act for 10-15 minutes and then intervene with a brush, single-brush machine with green disc or pressure washer.

4) Rinse with plenty of water. Clean tools thoroughly immediately after use.

FILA NO-RUST

RUST REMOVER

1) Apply the product on the stain to be removed, covering it completely.

2) Leave to act for about 15 minutes.

3) The product will take on an intense purple color, a sign of reaction with the rust present.

4) After the indicated time, remove
the product residue and rinse thoroughly with clean water, leaving to dry.

5) If necessary, the application can be repeated.

FILA NO-SPOT

SPRAY STAIN REMOVER FOR KLINKER COTTO AND NATURAL STONE

1. Spray from a distance of 15 cm, holding the can at an angle of approximately 45°.

2. Leave to dry for a few minutes. A fine white powder will form which will capture the dissolved greasy dirt.

3. Remove with a brush. 

4. Wipe with a damp cloth. If streaks remain, repeat the operation.

FILA PS87

WAXING AND DEGREASING DETERGENT

To clean and degrease all surfaces Dilute in water (1:10-1:20) and apply to the surface. Leave to act for 4-5 minutes and then clean with a single disc machine or scrubbing brush. Collect with a wet vacuum or rag and rinse well. For more vigorous cleaning, dilute 1:5. To remove stains from porcelain stoneware Pour pure on the stain and all over the tile. Leave to act until completely dry, wash and rinse. To dewax Dilute 1:5, apply and leave to act for 10 minutes. Intervene with a brush or single brush. Collect with a cloth vacuum cleaner and rinse well.

FILA SOLV

WAXER FOR SOLVENT-BASED WAXES

Soak a rag thoroughly with FILA SOLV and clean the surface, taking care not to redistribute wax or waterproofing residues. In more stubborn cases, pour FILA SOLV directly onto the surface, distribute it and leave it to act for a few minutes and intervene vigorously with a brush. It is advisable to work on small areas and collect the dissolved dirt with a rag.

HYDROREP

SOLVENT BASED WATER-REPELLENT PROTECTIVE

On a perfectly clean and dry surface, apply evenly with a brush. On vertical surfaces, apply by spray (airless system), dosing the product to waste. The product should be applied depending on the absorbency of the support, in one or two coats, 24 hours apart. For slightly absorbent natural stones (e.g. slate) in one coat; for concrete and more absorbent natural stones, in two coats. In the case of external surfaces to which you also want to impart oil repellency, apply a finishing coat of FIlafob after 24 hours.

SALVATERRAZZA®

SOLVENT BASED ANTI-INFILTRATION CONSOLIDATING PROTECTIVE

The treatment must be carried out on a dry and clean floor. For thorough cleaning, use the SALVATERRAZZA® FASEZERO concentrated preparatory remover. Once the floor is dry, apply SALVATERRAZZA® evenly over the entire surface with a brush or other applicator, soaking the joints and cracks well. Massage the surface within 5 minutes with a cloth or absorbent paper to dry and completely remove excess product.